Bodyguard T270 Manuel d'instructions télécharger pdf (Page 48)

TREADMILLS – OWNER’S MANUAL

5.10. ESC TEST

The ESC test allows you to see the effect of the ESC feature while using the treadmill.

1. Enter the DIAGNOSTICS Menu, select ESC TEST and press JustGo

to accept. (T240S-T280S-T520S: select “d7”)

The motor will start and the belt will reach a speed of 2.0 mph (or 3.2 km/h).

2. You should see ESC ON (ON on S Consoles) appearing at the bottom of screen. This indicates that if you incline the

treadmill, the ESC function will prevent you from over speeding the belt and exceeding the specified speed.

3. Increase the incline up to 15% to get the best demonstration of this feature.

4. Next, press the iTek button once. ESC OFF (OFF on S Consoles) should be displayed on screen. This means the ESC

function has been disabled. The belt may over speed and cause unsteadiness depending on the weight of the user and

the belt speed. This allows you to feel the difference of a unit with or without ESC.

5. Press the STOP key to terminate the test.

5.11. SPEED SENSOR TEST

The speed sensor test allows you to see whether your speed sensor circuit is functional or not.

1. In the DIAGNOSTICS Menu, select the SPEED SENSOR TEST (T240S-T280S-T520S: select “d3”) and press the

JustGo

key to accept.

2. Let the belt reach a speed of 2.0 mph or 3.2 km/h. The message will be displayed in the central information window

indicating whether the sensor is good or bad.

On a T240S-T280S-T520S a value of ‘0’ (BAD) or ‘1’ (GOOD) will flash in the bottom left LED window.

If the message indicates BAD, check the following items:

• Check of your speed sensor is connected to the electronic card.

• Check the optical disk to make sure the sensor is not dirty.

3. Press the STOP key to terminate the test.

5.12. ERROR LOG

The error log allows you to see the number of times an error has occurred.

1. In the DIAGNOSTICS Menu, select ERROR LOG (T240S-T280S-T520S: select “d4”) and press the JustGo

key.

2. You will see all the errors and the number of times each one occurred by using the DECREASE SPEED key.

3. Press the JustGo

key to reset the error codes (T240S-T280S-T520S: select rES to reset all errors and press

JustGo

key to confirm) or press the STOP key to exit this section.

NOTE – The table of errors can be viewed at the end of this document.

5.13. MAINTENANCE

The maintenance menu allows you to see the average value of the current drawn by the motor. It also allows you to reset

this counter.

A first threshold has been set to make ensure that too high a limit of current drawn by the motor will not occur. When that

first level is reached, a user with a T240S-T280S-T520S will get the message “D6-1” displayed on the main screen. The user

with a T260P-T260F-T270-T280P-T460XC-T520P-T560X will get the message “DECK SURFACE MAINTENANCE

REQUIRED” and symbol “!” will be displayed on the main screen (see table below). The message will be displayed between

each new exercise. After the maintenance has been done, reset the maintenance counter in the DIAGNOSTICS Menu. The

warning notice will not reappear until the 1

threshold is reached again.

If the maintenance is not done on the deck surface when required, a second threshold will trigger 0.5 amps above the first.

Another notice will appear on the main display. Users with a T240S-T280S-T520S will get the message “D6-2” displayed on

the main screen. Users with a T260P-T260F-T270-T280P-T460XC-T520P-T560X will get the message “DECK SURFACE

MAINTENANCE REQUIRED” and symbol “X” will be displayed on the main screen (see table below). At this point, the

machine will not start again until the deck maintenance is done and the maintenance counter reset in the DIAGNOSTICS

Menu.

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Commentaires sur ces manuels

Pas de commentaire

Bodyguard T270 Manuel d'instructions Page 48

Commentaires sur ces manuels

Produits connexes et manuels pour Tapis de course Bodyguard T270